Your car might have an alignment problem if: it drifts or pulls to one side, your steering wheel’s off center, you have uneven tire wear or your car doesn’t feel like it handles right. When all of a vehicle’s wheels are lined up exactly with each other, your wheels are in alignment. Running into potholes, smacking a curb or other object are great ways to knock your car out of alignment. Then one or more of your wheels starts pulling in a slightly different direction and the problems begin.
Driving for an extended time when you’re out of alignment causes your tires to wear unevenly and excessively. This can be dangerous and expensive. You’ll have to replace your tires sooner, but even worse – you may cause premature wear to your suspension system, which can be really expensive.
The front wheel alignment is adjustable on all vehicles, and the back wheels are also adjustable on some cars. The adjustment can go three different ways. The first adjustment is called toe. The next adjustment is called camber. And finally, there is castor. The engineers who designed your vehicle determined the alignment settings that will give you the best handling and safety.
There are several things involved in an alignment check. First, there’s an inspection of the steering and suspension – it should be checked to see if anything’s bent or broken. Then the tire condition needs to be inspected. From there, the vehicle is put on an alignment rack and an initial alignment reading is taken. If all four wheels are adjustable, they are lined up perfectly parallel with the vehicle’s center line. If the back wheels aren’t adjustable, the technician determines the direction they push and then aligns the front wheels to match.
Like most things, your manufacturer has suggested a mileage interval for having your alignment checked. But if you run into a curb, pothole or something else that’s given you a big jolt, pay attention to whether your vehicle is pulling to one side when you drive. It’s better to have your alignment checked before waiting to see if there is uneven tire tread wear – by then, the damage is done.
Getting your alignment checked when needed is a great way to extend the life of your tires and suspension parts. It also makes sure that your tire meets the road properly for maximum performance and safety. For more information about alignment, call Houska Automotive at 970-482-0156.
Something you’re going to be hearing a lot about around Fort Collins, Colorado is diesel engines. We’re not talking about semi-trucks and buses – We’re talking about diesel engine cars, pick-ups and SUVs.
Most people in Fort Collins, Colorado are surprised to learn that around half the cars on the road in Europe have diesel engines. Nearly all import auto manufacturers offer a range of diesel engines abroad – even the ultra-luxury brands like Mercedes and BMW. For the most part, these diesel engines haven’t been available in Fort Collins, Colorado. But that’s about to change.
In the past, North American diesel fuel has had a much higher sulfur content than European fuel. Recent environmental laws have required changes in diesel formulation and emissions standards here in Fort Collins, Colorado so we are now ready to start seeing more diesel options offered over the next few years.
Why are so many interested in diesel engines? Well first off, diesel fuel is more energy dense. There’s more power in a barrel of diesel fuel than there is in a barrel of gasoline. That means better performance with better fuel economy.
Diesel powered vehicles get about 20 percent better fuel economy. And as for power – why do you think that the majority of new heavy duty pick-up trucks are being sold with diesel engines?
If you think back to the late 1970’s and early 1980’s, you may shudder when you think of the diesel powered cars of the day – noisy, smoky, under-powered beasts that rattled and shook their passengers. Modern diesels are nothing like that.
They are quiet, clean – and very powerful. They’re so refined that many people can’t even tell they’re riding in a diesel powered car. In addition to fuel savings, diesels generally last longer than gasoline engines because of their heavy duty construction.
Another thing that intrigues the environmentally conscious is that it’s possible to use bio-diesel as fuel. Bio-diesel is made from vegetable oil – even recycled cooking oil from restaurants. Hybrid cars have gotten everyone’s attention these days. Look to diesel-electric hybrids in years to come to make a good idea even better.
Every year, manufacturers are planning more diesel offerings. Look for diesels in domestic light trucks, SUVs and passenger cars. Import marquees have plans to bring more of their outstanding diesel engines to Fort Collins, Colorado as well.
Now you should know that properly maintaining a diesel engine is somewhat different than a gasoline engine. Fluid change intervals are different. Emissions control devices have to work harder to filter diesel fuel and to scrub the exhaust so you will need to pay attention to that. And the fuel injection system operates at much higher pressures than gas fuel injection systems, so it’s very important to keep your fuel system clean with a diesel.
The good news is that your local Fort Collins, Colorado service center is keeping up with the new diesel technology and will be able to advise you on maintaining your diesel.
When we tell you to look for more diesels, you won’t be looking for smoky tail pipes as a clue. You also won’t be listening for that familiar big rig rattle. And, you certainly won’t be waiting for them at the stoplight, because modern diesels are as quick as their gasoline counterparts.
From all of us at AutoNetTV, ten four, good buddy.
North Americans love their cars. And nothing goes with cars better than the road trip. Freedom from daily schedules, new sights and the open road – it’s great! But there’s nothing like car trouble to bring the fun to a grinding halt.
Now you can’t always avoid problems, but you can take steps to reduce the probability of getting sidelined on your trip. The first step is to look at your trip plan from your vehicle’s perspective. What kind of roads will you be traveling – winding byways or super-highways? Mountains or plains? What weather conditions are you likely to encounter? How many miles will you travel? How much weight will you be hauling – passengers and luggage? Lugging a trailer or roof top carrier? Will it be dusty?
Armed with the answers to these questions, you can start a trip inspection to help you prepare your Fort Collins vehicle for your big adventure. A lot of our Fort Collins customers prefer to go through this exercise with an automotive service advisor at Houska Automotive to get their input and make sure they haven’t left anything out.
A great place to start is with the tires. Inspect them for tread wear and proper inflation. Is it time to rotate your tires? Replace them? Are they up to the job – you wouldn’t want to drive regular highway tires on a muddy off-road adventure.
Shocks and struts play a major role in both driving comfort and safety. If they need to be replaced, you’ll really be glad you did once you hit the road. Is it time for a wheel alignment? Fighting a car that’s pulling to one side all day can be tiring and dangerous.
And don’t forget your brakes. Any strange noises, grabbing, soft or hard peddle feel? If there is any doubt, get a brake inspection before you leave.
Moving under the hood, have your belts and hoses inspected. If something is excessively worn or near failure, the stress of a long road trip might just be the straw that breaks the camel’s back.
Your engine air filter will be important. For every gallon of gas you burn, your car will filter and use 12,000 gallons of air. If the filter needs to be changed, you’ll notice the fuel savings on your trip.
How close are you to your next oil change? Will you be able to complete your trip before it’s due? If not, just get it taken care of before you go so that you don’t need to interrupt your trip. In fact, a full service oil change is a great idea because they will top off all your fluids and check to see if any other maintenance items are due, such as transmission or cooling system service.
Do you notice any unusual odors in your vehicle? If so, it could as harmless as a dirty cabin air filter. But if it’s an exhaust leak it could be fatal on a long trip. Of course you’ll want to be comfortable, so get an air conditioning service if you aren’t getting the cold air you used to.
Are you wiper blades still working well? If not, that is quick and inexpensive to fix. Headlamps are often overlooked when planning for a trip. If you haven’t changed the bulb in six months or so, replacement bulbs will really light up the night on your trip.
All the items mentioned are part of any good vehicle maintenance plan. These are things that you want to take care of anyway, but they all come into focus as you plan for your trip.
They will always save you money in the long run and may prevent inconvenient delays on your trip. After all, you wouldn’t want to miss the world’s largest ball of string, would you?
Here at AutoNetTV, we have viewers, like you, from all across the country who write to us with questions or feedback. One common question we’re asked is: What is a differential and what does it do? You may have been told your differential needs service, or seen it as an option up on the service menu. Differential service covers a lot of things, so let’s first talk about what a differential does.
As you drive through a turn, your outside wheels and inside wheels turn at different speeds. Kind of like the cars going around a race track – the ones driving in the outside lanes have a greater distance to travel than the cars in the inside lanes. The differential is what allows the outside and inside drive wheels to rotate at slightly different speeds so that the tires don’t hop or skip while taking corners, or lose traction in dirt or snow. Differentials have gears in them that transfer the power from the drive train to your wheels – which is why they’re often referred to as gear boxes. The gears need to be very strong to do this work, and they need to be properly protected so that they’ll last.
All vehicles have some form of differential. If you have a front-wheel drive car, your differential is often called a transaxle and is located in the front. If you have rear-wheel drive, the differential is in the back of the car. If you have a four-wheel drive vehicle, you will have a differential in the front and the back – and in the middle as well. The center differential adjusts for differences in speed between the front and rear wheels.
Differential fluid lubricates and cools the gears. Over time, the fluid can get dirty from bits of the gears grinding off. The additives that keep the fluid clean and protect the differential break down over time. So your vehicle manufacturer has scheduled intervals for you to have your differential fluid changed.
Differentials are hard working mechanisms, and, along with the gears in a manual transmission, need to be serviced regularly with high-quality, replacement fluid. Your Denver automotive service advisor can give you more information as to when your next differential service is recommended. You can also ask if they have a record of when the service was last completed.
As with most service intervals, if you are driving under more severe conditions, you will want to service your differential more frequently. “Severe service” conditions are defined in most owners’ manuals, and include: frequent starts and stops, short trips, cold weather, hot weather and towing. All these conditions add to the stress of the vehicle and its parts. Also, off-roading in Colorado can be especially hard on differentials, especially if you cross streams. Proper service will extend the life of your gears and keep them running more smoothly. If you have never had your differential checked, visit http://houskaautomotive.com/contact-us.shtml for more information.
The energy from exploding fuel is what powers your engine. But some of the vapors from the explosions escape into the lower part of the engine, called the crankcase. The crankcase is where your engine oil hangs out. These gases are about 70% unburned fuel. If the gases were allowed to stay in the crankcase, they would quickly contaminate the oil and turn it to sludge. Sludge is one of the biggest enemies of your engine, clogging it up, eventually leading to expensive failures. Also, the pressure build up would cause seals and gaskets to blow out. Therefore, these gases need to be vented out.
Gasoline engines used to simply have a hose that let the poisonous fumes vent out into the air. In 1963, the federal government required gas engines to have a special one-way valve installed to help reduce dangerous emissions. Diesel engines are not required to have these valves.
The positive crankcase ventilation, or PCV, valve routes crankcase gases through a hose and back into the air intake system where they are re-burned in the engine. Fresh, clean air is brought into the crankcase through a breather tube. It’s really a pretty simple system, but does an important job. The re-circulating air removes moisture and combustion waste from the crankcase, preventing sludge. This extends not only the life of your oil, but the engine as well. The PCV relieves pressure in the crankcase, preventing oil leaks.
Eventually, the PCV valve can get gummed up. Then it can not move enough air through the engine to keep it working efficiently. If the PCV valve is sticking enough, you could have oil leaks, excess oil consumption and a fouled intake system. If you experience hesitation or surging or an oil leak, it may be a sign of PCV value problems. Your owners’ manual may give a recommendation for when the PCV valve should be replaced – usually between 20,000 mi/32,000 km and 50,000 mi/80,000 km. Unfortunately, some manufacturers don’t list a recommendation in the manual, so it can be easy to overlook.
Many PCV system problems can be diagnosed with a visual inspection. Fortunately, PCV valve replacement is both quick and inexpensive. Proper oil changes will greatly extend the life of the PCV valve. Skipping a few recommended oil changes can allow varnish and gum to build up in the valve, reducing its efficiency. So now when your Fort Collins service technician tells you its time to replace your PCV valve, you will know what he’s talking about. If you have had your car for a while and this is the first you’ve ever heard of a PCV value, ask your tech to check yours out or call Houska Automotive at 970-482-0156.
A lot of our viewers have asked whether or not they should use their severe service maintenance schedule, which is listed in their car owners’ manual. It can be confusing. Let’s clear the air on this subject. Cricket Killingsworth is from QMI/Heartland, a manufacturer of automotive products and fluids. She’s been in the automotive business for 20 years and is a speaker, a trainer, and a writer. Cricket says there’s so much confusion on this topic because, “Most owners’ manuals actually have two maintenance schedules. Sometimes these are called ‘regular service’ and ’severe service’. Sometimes they’re simply called Schedule 1 and Schedule 2. A severe service schedule recommends that things like an oil change, air filter replacement, and transmission service be done more often: either in fewer miles or in less time.
Manufacturers create these specific schedules for each vehicle they make. So there isn’t one generic schedule that applies to all cars. In addition to your owners’ manual, Fort Collins automotive repair centers subscribe to information services that provide the maintenance schedules for every vehicle – so they can help you know when to take care of needed services. Below is a typical definition for severe service.
Most trips are less than four miles
Most trips are less than ten miles and outside temperatures are below freezing
You drive in very hot weather
The engine is at low speed most of the time (not on the highway)
Stop and go driving
You operate your vehicle in dusty or muddy conditions
You tow a trailer, regularly carry heavy loads or carry a car-top carrier
It’s common sense: Just a few minutes at freeway speeds allows the moisture in the oil to evaporate. Very short trips, or trips of less than ten miles when it’s very cold, don’t allow the engine to heat up enough to get rid of the water. And water in the oil leads to damaging sludge. Also, towing and heavy loads raise operating temperatures and cause fluids to breakdown more quickly. Dusty and muddy driving means that more dirt will get past the air filter to contaminate the fuel system and engine oil.
The bottom line is that you need to decide for yourself if the regular or severe service schedule is right for you, based on your driving. Look at your owners’ manual, or talk with your Houska Automotive service advisor who can help you know which schedule to follow. Houska Automotive is located at 899 Riverside Avenue, Fort Collins Colorado.,
Here is what a fleet manager said recently: “Since city miles are generally tougher on vehicles than highway miles, we use the manufacturer’s severe service schedule as the basis for our preventative maintenance program. We massage those schedules over time, increasing or decreasing the service intervals so that they make the most sense. There is a little bit of art to go along with the science.
Make an honest evaluation of your driving habits. Unless you do mostly Colorado highway driving in moderate weather, you’ll likely have a fairly good amount of severe service mixed in. Some people just want to play it safe and follow the severe service recommendations, rather than analyzing how they drive each month.
We would like to give you an update on some of the things happening in automotive fluids. You know, cars are becoming more sophisticated everyday – and fluids such as, oil, coolant and transmission fluid are becoming more specialized at about the same pace.
The do-it-yourselfer has to be pretty careful so that they do not actually harm their vehicle with the wrong type of fluid. That is why so many Colorado car owners rely on the advice of their service consultant to not only get the correct family of fluids, but to suggest the formulation that is best for their car and the way they drive.
Let’s start with engine oil. If you have been paying attention, you will have noticed a number of new oil weights on the scene in the last several years. Modern engines are built to much tighter tolerances and have very complicated valve trains. The oil must be thin enough to lubricate complicated parts when the engine is cold. The weight of an oil is expressed in terms like 20-W-50 or 5-W-30. Manufacturers recommend the weight of oil for each vehicle they make. The recommendation is based on engine design. Your Fort Collins service center will know what weight your manufacturer recommends – and it’s important to follow those recommendations. A service adviser at Houska Automotive can also offer suggestions for special formulations and can explain conventional and synthetic oils.
Antifreeze, or engine coolant, is another area that has become more complicated. For a long time, manufacturers only called for a couple of different types of coolant. Now there are several different formulations that are needed because of the different materials that manufacturers are using to build the cooling system. Using the wrong type of coolant can actually void your warranty, so you want to get that right.
Transmission fluid is beginning to be specialized as well. New transmission designs have particular requirements that mandate the use of specific formulations. Recently, new, somewhat confusing, standards for brake fluid have also been released.
Not too long ago, there was a good chance that all of the vehicles at your house would use many of the same fluids. However, as automotive technology advances, the array of basic automotive fluids you need will grow. And, some of the formulations will cost a little more. Fortunately, your Denver service center will continue to update their training to keep pace with technology so that you’ll get the right fluids your car needs. It’s all part of the commitment your service center makes to your driving peace of mind.
What type of technology do you use? Do you prefer an 8-track tape or an iPod? When it comes to winter tires, much of the public’s perception dates back to when 8-track was the best way to listen to the Bee Gees.
Twenty years ago, winter tires differed from highway tires only in their tread design. We called them snow tires back then and they had big, knobby lugs that were designed to give good traction in deep snow. They had the same rubber compound as regular tires and they weren’t very good on ice, packed snow or wet roads. They were not even very good on dry roads. They really helped in deep or loose snow, but they did a poor job the rest of the time. They were loud and rode hard. You couldn’t wait to get them off in the spring.
Then all-season tires started to come along. All-season tires are really a compromise between summer and winter performance. They have acceptable hot weather ride and tread life, and you can get through mild winter road conditions OK. But there are some really good reasons to consider winter tires.
Modern winter tires do a terrific job in a wide range of winter conditions. First of all, below 45 degrees Fahrenheit, regular tires become hard and inflexible. That means they don’t provide the road grip you need. Even if you don’t live somewhere with a lot of snow, but it still gets below 45 degrees in the winter, you will be safer with winter tires.
In addition, they are specifically designed to more effectively move snow and water. That’s the key to traction on ice, packed snow and wet roads. They use a micro-pore compound that allows the tire to bite into ice and snow. They also use wider grooves that run around the circumference of the tread to expel snow from the tire better. The lugs and grooves on winter tires have a special shape that throws the packed snow out of the tread as the tire turns. The tread is then open when it comes back in contact with the road and can provide good traction.
Winter tires also have a lot of sipes. Sipes are thin slits in the tread. The edge of the sipes grab ice and packed snow to provide tons of traction and to expel water and slush out of the tread. winter tires have a rounder casing to cut into the snow’s surface. The treads on regular summer tires can actually get packed with snow instead and become very slick. winter tires offer 25% to 50% more traction than all-season tires. And when it comes to stopping power, all-season tires take 42% longer to stop than winter tires. Sometimes that’s the difference between getting home safely and spending the night in a snow bank.
Now back when the 8-track was king, you just put snow tires on the drive wheels. That worked out OK because the rubber compound was essentially the same. Now, winter tires provide so much more traction than all-season or summer tires, that there’s a huge difference between the traction at the front and rear ends of the car if you only put winter tires on the drive wheels.
For example: if you take a corner on an icy road and the rear end starts to slide out, essentially the rear is trying to pass the front because it’s going faster. If you have high traction winter tires only on the front, they are going to be much more effective at transferring cornering grip and stopping power to the front wheels. This will actually cause the rear end to whip out even more.
That’s why tire manufactures instruct their dealers that they must install winter tires on the rear wheels as well whenever they put winter tires on the front end of any vehicle. It’s a major safety concern. It’s strongly recommended that winter tires be installed on all four wheels on rear wheel drive vehicles as well. The front tires do most of the steering and braking work – it only makes sense that you provide the front end with the best traction you can.
People often assume that if they have four-wheel drive or all-wheel drive they don’t need winter tires on all four wheels. Would you intentionally disconnect the four-wheel drive in poor road conditions? Of course you wouldn’t, but that’s essentially what you do if you only put winter tires on one end. It only makes sense to have the same level of traction and control at all four corners.
The province of Quebec in Canada has issued a law requiring all passenger vehicles, taxis and rental cars with Quebec license plates to install a full set of four winter tires between November 15th and April 1. It’s that important.
Many modern cars have traction control and anti-lock brakes so people may think that they don’t need winter tires. But you need traction to accelerate, steer and stop. The tires provide the traction so that the traction control and anti-lock brakes have something to work with.
Look for tires with the symbol of a mountain with a snowflake in it. This means the tire complies with the severe snow standard. All-season tires will have an M&S, for mud and snow, on the sidewall.
So when the temperatures drop below 45 degrees, be sure you have a set of four winter tires for maximum performance in snow, packed snow, ice, wet and dry roads. Your tire professional can help you find the right winter tire for your vehicle and driving needs.
The coolant system is a vital part of your vehicle. It is also the second most common cause for vehicle failures. Even though coolant system failure is fairly common, it is easy to prevent.
The most recognizable part of the coolant system is the radiator. It is connected to the engine with hoses and is filled with coolant. The coolant draws heat off the engine and then goes into the radiator. Air passes through cooling fins to reduce the temperature of the coolant and then it’s back to the engine again.
There are several ways for the cooling system to fail. Most common is with the coolant itself. Coolant is a mixture of water and antifreeze. The proper mixture keeps the coolant from either boiling away or freezing. Both of which can result in massive engine damage.
Another very important coolant issue that is often overlooked is the age of the coolant itself. antifreeze has additives that protect the coolant system from corrosion. As these additives are depleted over time, they can’t protect the radiator and other parts from rust, scaling and corrosion. Old coolant may still keep your engine cool, but it won’t protect it from corrosion.
If you see a warning message to check the coolant or if the temperature gauge is in the hot zone your cooling system needs to be checked. It’s OK to add water or antifreeze yourself. But you need to be cautious. Remember four things.
First, you never want to open the radiator pressure cap. You could be severely burned.
Second, try to get to a Fort Collins service center such as Houska Automotive immediately if your coolant is low. If that is not possible, follow the directions in your owners manual – it will direct you to only make additions to the coolant overflow bottle.
Third, remember that you need a proper mixture of water and antifreeze. If you make an emergency addition to your cooling system, follow-up with your service center where they can make necessary corrections.
Fourth, not all cars use the same type of antifreeze. You need to check your owners manual to make sure you use the right kind. Mixing antifreeze types or using the wrong kind of antifreeze may void the manufacturers warranty on your cooling system. Again, another reason to rely on your Fort Collins service center to do things right.
Remember, Houska Automotive has the equipment to change your coolant quickly and inexpensively. 970-482-0156
The last new car sold with a carburetor in North America rolled out of the dealership in 1990. Since then, all new vehicles have had fuel injectors. In very simple terms, a fuel injector is a valve that squirts fuel into your engine. Your engine control computer tells the fuel injector how much gas to deliver as well as the precise time it should be delivered. Of course this happens thousands of times a minute. Fuel injection is a much more precise way of delivering fuel than carburetors. That translates into better fuel economy and power. Virtually all fuel injectors for gas engines are known as port fuel injectors because they deliver the fuel to a port just outside the cylinder. Port fuel injectors operate at about 40 to 80 pounds per square inch of pressure.
A few auto makers have introduced gas direct injection systems on some engines recently. These systems inject the gas directly into the cylinders under very high pressure – hundreds of times the pressure of port injection systems. Although more complicated, direct injection technology promises greater power with improved fuel economy, so we can expect to see more of it in the future.
As you can see, the level of precision required of your fuel injectors is very high. They need to be operating properly in order for your car to run right.
High temperatures under your hood and variations in gas quality cause fuel injectors to become fouled with wax, dirt, and carbon. Injectors can become partially clogged, preventing them from delivering the proper amount of fuel at the correct pressure. The design of each engine requires a specific spray pattern from the fuel injector that might be altered when the injector is dirty. When injectors are dirty, the fuel doesn’t burn as efficiently resulting in poor fuel economy and loss of power. So it is important to keep your fuel injectors clean.
Skilled service technicians at Houska Automotive in Fort Collins can perform a fuel system service for you. (Visit http://houskaautomotive.com/contact-us.shtml.) That is a fuel system service – not just fuel injector cleaning. That is because the fuel has a lot of ways to become dirty or contaminated between the gas tank and the fuel injector. A fuel system service starts with a fuel filter replacement. This filter cleans the gas as it leaves the tank. The various parts of the fuel intake system need to be cleaned from time to time to remove harmful gum, deposits and varnish. Finally, the fuel injectors are cleaned so that they operate properly and deliver the right amount of fuel at the right time.
Your Loveland area service center uses a process for cleaning your fuel system that includes state-of-the-art cleaning chemicals as well as some old fashioned scrubbing. Proper maintenance of your fuel system means that you will spend less on gas, enjoy strong performance and prevent costly repairs down the road.
